-# Sample Configuration File for Privoxy v3.0.7
+# Sample Configuration File for Privoxy v3.0.19
#
-# $Id: config,v 1.60 2007/12/08 14:30:40 hal9 Exp $
+# $Id: config,v 1.97 2011/11/19 15:20:23 fabiankeil Exp $
#
-# Copyright (C) 2001-2007 Privoxy Developers http://www.privoxy.org/
+# Copyright (C) 2001-2011 Privoxy Developers http://www.privoxy.org/
#
####################################################################
# #
#
#
# 1. LOCAL SET-UP DOCUMENTATION
+# ==============================
#
# If you intend to operate Privoxy for more users than just yourself,
# it might be a good idea to let them know how to reach you, what
#
#
# 1.1. user-manual
+# =================
#
# Specifies:
#
#
# user-manual /usr/share/doc/privoxy/user-manual
#
-#
# The User Manual is then available to anyone with
# access to Privoxy, by following the built-in URL:
# http://config.privoxy.org/user-manual/ (or the shortcut:
#
# user-manual http://example.com/privoxy/user-manual/
#
-#
# WARNING!!!
#
# If set, this option should be the first option in the config
#
#
# 1.2. trust-info-url
+# ====================
#
# Specifies:
#
#
# Default value:
#
-# Two example URLs are provided
+# Unset
#
# Effect if unset:
#
# don't end up locked out from the information on why they were
# locked out in the first place!
#
-trust-info-url http://www.example.com/why_we_block.html
-trust-info-url http://www.example.com/what_we_allow.html
+#trust-info-url http://www.example.com/why_we_block.html
+#trust-info-url http://www.example.com/what_we_allow.html
#
#
# 1.3. admin-address
+# ===================
#
# Specifies:
#
#
#
# 1.4. proxy-info-url
+# ====================
#
# Specifies:
#
#
#
# 2. CONFIGURATION AND LOG FILE LOCATIONS
+# ========================================
#
# Privoxy can (and normally does) use a number of other files for
# additional configuration, help and logging. This section of the
#
#
# 2.1. confdir
+# =============
#
# Specifies:
#
#
#
# 2.2. templdir
+# ==============
#
# Specifies:
#
#
#
# 2.3. logdir
+# ============
#
# Specifies:
#
-# The directory where all logging takes place (i.e. where logfile
-# and jarfile are located).
+# The directory where all logging takes place (i.e. where the
+# logfile is located).
#
# Type of value:
#
#
#
# 2.4. actionsfile
+# =================
#
# Specifies:
#
#
# Default values:
#
-# standard.action # Internal purposes, no editing recommended
+# match-all.action # Actions that are applied to all sites and maybe overruled later on.
#
-# default.action # Main actions file
+# default.action # Main actions file
#
-# user.action # User customizations
+# user.action # User customizations
#
# Effect if unset:
#
# Multiple actionsfile lines are permitted, and are in fact
# recommended!
#
-# The default values include standard.action, which is used
-# for internal purposes and should be loaded, default.action,
-# which is the "main" actions file maintained by the developers,
-# and user.action, where you can make your personal additions.
+# The default values are default.action, which is the "main"
+# actions file maintained by the developers, and user.action,
+# where you can make your personal additions.
#
# Actions files contain all the per site and per URL configuration
# for ad blocking, cookie management, privacy considerations,
# was necessary to be consistent with the other file options and
# to allow previously forbidden characters.
#
-actionsfile standard.action # Internal purpose, recommended
+actionsfile match-all.action # Actions that are applied to all sites and maybe overruled later on.
actionsfile default.action # Main actions file
actionsfile user.action # User customizations
#
#
# 2.5. filterfile
+# ================
#
# Specifies:
#
# separate file, such as user.filter.
#
filterfile default.filter
-#filterfile user.filter # User customizations
+filterfile user.filter # User customizations
#
#
# 2.6. logfile
+# =============
#
# Specifies:
#
#
# Effect if unset:
#
-# Logging is disabled unless --no-daemon mode is used.
+# No logfile is written.
#
# Notes:
#
# an ad you think it should block) and it can help you to monitor
# what your browser is doing.
#
-# Depending on the debug options below, the logfile may be a privacy
-# risk if third parties can get access to it. As most users will never
-# look at it, Privoxy 3.0.7 and later only log fatal errors by default.
+# Depending on the debug options below, the logfile may be a
+# privacy risk if third parties can get access to it. As most
+# users will never look at it, Privoxy 3.0.7 and later only log
+# fatal errors by default.
#
-# For most troubleshooting purposes, you will have to change that, please
-# refer to the debugging section for details.
+# For most troubleshooting purposes, you will have to change that,
+# please refer to the debugging section for details.
#
# Your logfile will grow indefinitely, and you will probably
# want to periodically remove it. On Unix systems, you can do
# Any log files must be writable by whatever user Privoxy is
# being run as (on Unix, default user id is "privoxy").
#
-#logfile logfile
-#
-#
-# 2.7. jarfile
-#
-# Specifies:
-#
-# The file to store intercepted cookies in
-#
-# Type of value:
-#
-# File name, relative to logdir
-#
-# Default value:
-#
-# Unset (commented out). When activated: jarfile (Unix) or
-# privoxy.jar (Windows).
-#
-# Effect if unset:
-#
-# Intercepted cookies are not stored in a dedicated log file.
-#
-# Notes:
-#
-# The jarfile may grow to ridiculous sizes over time.
-#
-# If debug 8 (show header parsing) is enabled, cookies are also
-# written to the logfile with the rest of the headers. Therefore
-# this option isn't very useful and may be removed in future
-# releases. Please report to the developers if you are still
-# using it.
-#
-#jarfile jarfile
+logfile logfile
#
#
-# 2.8. trustfile
+# 2.7. trustfile
+# ===============
#
# Specifies:
#
#
#
# 3. DEBUGGING
+# =============
#
# These options are mainly useful when tracing a problem. Note that
# you might also want to invoke Privoxy with the --no-daemon command
#
#
# 3.1. debug
+# ===========
#
# Specifies:
#
-# Key values that determine what information gets logged to
-# the logfile.
+# Key values that determine what information gets logged.
#
# Type of value:
#
#
# Default value:
#
-# 12289 (i.e.: URLs plus informational and warning messages)
+# 0 (i.e.: only fatal errors (that cause Privoxy to exit) are logged)
#
# Effect if unset:
#
-# Nothing gets logged.
+# Default value is used (see above).
#
# Notes:
#
# The available debug levels are:
#
-# debug 1 # show each GET/POST/CONNECT request
-# debug 2 # show each connection status
-# debug 4 # show I/O status
-# debug 8 # show header parsing
-# debug 16 # log all data written to the network into the logfile
-# debug 32 # debug force feature
-# debug 64 # debug regular expression filters
-# debug 128 # debug redirects
-# debug 256 # debug GIF de-animation
-# debug 512 # Common Log Format
-# debug 1024 # debug kill pop-ups
-# debug 2048 # CGI user interface
-# debug 4096 # Startup banner and warnings.
+# debug 1 # Log the destination for each request Privoxy let through. See also debug 1024.
+# debug 2 # show each connection status
+# debug 4 # show I/O status
+# debug 8 # show header parsing
+# debug 16 # log all data written to the network
+# debug 32 # debug force feature
+# debug 64 # debug regular expression filters
+# debug 128 # debug redirects
+# debug 256 # debug GIF de-animation
+# debug 512 # Common Log Format
+# debug 1024 # Log the destination for requests Privoxy didn't let through, and the reason why.
+# debug 2048 # CGI user interface
+# debug 4096 # Startup banner and warnings.
# debug 8192 # Non-fatal errors
+# debug 32768 # log all data read from the network
#
#
# To select multiple debug levels, you can either add them or
# use multiple debug lines.
#
# A debug level of 1 is informative because it will show you each
-# request as it happens. 1, 4096 and 8192 are recommended so that you
-# will notice when things go wrong. The other levels are probably only
-# of interest if you are hunting down a specific problem. They can
-# produce a hell of an output (especially 16).
-#
-# Privoxy used to ship with the debug levels recommended above enabled
-# by default, but due to privacy concerns 3.0.7 and later are
-# configured to only log fatal errors.
-#
-# If you are used to the more verbose settings, simply enable the debug
-# lines below again.
+# request as it happens. 1, 1024, 4096 and 8192 are recommended
+# so that you will notice when things go wrong. The other levels
+# are probably only of interest if you are hunting down a specific
+# problem. They can produce a hell of an output (especially 16).
+#
+# Privoxy used to ship with the debug levels recommended above
+# enabled by default, but due to privacy concerns 3.0.7 and later
+# are configured to only log fatal errors.
+#
+# If you are used to the more verbose settings, simply enable
+# the debug lines below again.
#
# If you want to use pure CLF (Common Log Format), you should set
-# debug 512 ONLY and not enable anything else.
+# "debug 512" ONLY and not enable anything else.
#
# Privoxy has a hard-coded limit for the length of log messages. If
# it's reached, messages are logged truncated and marked with
# "... [too long, truncated]".
#
-# Please don't file any support requests without trying to reproduce
-# the problem with increased debug level first. Once you read the log
-# messages, you may even be able to solve the problem on your own.
+# Please don't file any support requests without trying to
+# reproduce the problem with increased debug level first. Once
+# you read the log messages, you may even be able to solve the
+# problem on your own.
#
-#debug 1 # show each GET/POST/CONNECT request
+#debug 1 # Log the destination for each request Privoxy let through.
+#debug 1024 # Log the destination for requests Privoxy didn't let through, and the reason why.
#debug 4096 # Startup banner and warnings
-#debug 8192 # Errors - *we highly recommended enabling this*
+#debug 8192 # Non-fatal errors
#
#
# 3.2. single-threaded
+# =====================
#
# Specifies:
#
#single-threaded
#
#
+# 3.3. hostname
+# ==============
+#
+# Specifies:
+#
+# The hostname shown on the CGI pages.
+#
+# Type of value:
+#
+# Text
+#
+# Default value:
+#
+# Unset
+#
+# Effect if unset:
+#
+# The hostname provided by the operating system is used.
+#
+# Notes:
+#
+# On some misconfigured systems resolving the hostname fails or
+# takes too much time and slows Privoxy down. Setting a fixed
+# hostname works around the problem.
+#
+# In other circumstances it might be desirable to show a hostname
+# other than the one returned by the operating system. For example
+# if the system has several different hostnames and you don't
+# want to use the first one.
+#
+# Note that Privoxy does not validate the specified hostname value.
+#
+#hostname hostname.example.org
+#
+#
# 4. ACCESS CONTROL AND SECURITY
+# ===============================
#
# This section of the config file controls the security-relevant
# aspects of Privoxy's configuration.
#
#
# 4.1. listen-address
+# ====================
#
# Specifies:
#
-# The IP address and TCP port on which Privoxy will listen for
+# The address and TCP port on which Privoxy will listen for
# client requests.
#
# Type of value:
#
# [IP-Address]:Port
#
+# [Hostname]:Port
+#
# Default value:
#
# 127.0.0.1:8118
#
# Effect if unset:
#
-# Bind to 127.0.0.1 (localhost), port 8118. This is suitable and
-# recommended for home users who run Privoxy on the same machine
-# as their browser.
+# Bind to 127.0.0.1 (IPv4 localhost), port 8118. This is suitable
+# and recommended for home users who run Privoxy on the same
+# machine as their browser.
#
# Notes:
#
# if you want to serve requests from other machines (e.g. on your
# local network) as well, you will need to override the default.
#
-# If you leave out the IP address, Privoxy will bind to all
+# You can use this statement multiple times to make Privoxy listen
+# on more ports or more IP addresses. Suitable if your operating
+# system does not support sharing IPv6 and IPv4 protocols on the
+# same socket.
+#
+# If a hostname is used instead of an IP address, Privoxy will
+# try to resolve it to an IP address and if there are multiple,
+# use the first one returned.
+#
+# If the address for the hostname isn't already known on the
+# system (for example because it's in /etc/hostname), this may
+# result in DNS traffic.
+#
+# If the specified address isn't available on the system, or if
+# the hostname can't be resolved, Privoxy will fail to start.
+#
+# IPv6 addresses containing colons have to be quoted by
+# brackets. They can only be used if Privoxy has been compiled
+# with IPv6 support. If you aren't sure if your version supports
+# it, have a look at http://config.privoxy.org/ show-status.
+#
+# Some operating systems will prefer IPv6 to IPv4 addresses even if
+# the system has no IPv6 connectivity which is usually not expected
+# by the user. Some even rely on DNS to resolve localhost which
+# mean the "localhost" address used may not actually be local.
+#
+# It is therefore recommended to explicitly configure the intended
+# IP address instead of relying on the operating system, unless
+# there's a strong reason not to.
+#
+# If you leave out the address, Privoxy will bind to all IPv4
# interfaces (addresses) on your machine and may become reachable
-# from the Internet. In that case, consider using access control
-# lists (ACL's, see below), and/or a firewall.
+# from the Internet and/ or the local network. Be aware that
+# some GNU/Linux distributions modify that behaviour without
+# updating the documentation. Check for non-standard patches if
+# your Privoxyversion behaves differently.
+#
+# If you configure Privoxyto be reachable from the network,
+# consider using access control lists (ACL's, see below), and/or
+# a firewall.
#
# If you open Privoxy to untrusted users, you will also
# want to make sure that the following actions are disabled:
# enable-edit-actions and enable-remote-toggle
#
+# With the exception noted above, listening on multiple addresses
+# is currently not supported by Privoxy directly. It can be done
+# on most operating systems by letting a packet filter redirect
+# request for certain addresses to Privoxy, though.
+#
# Example:
#
# Suppose you are running Privoxy on a machine which has the
#
# listen-address 192.168.0.1:8118
#
+# Suppose you are running Privoxy on an IPv6-capable machine and
+# you want it to listen on the IPv6 address of the loopback device:
+#
+# listen-address [::1]:8118
#
listen-address 127.0.0.1:8118
#
#
# 4.2. toggle
+# ============
#
# Specifies:
#
#
#
# 4.3. enable-remote-toggle
+# ==========================
#
# Specifies:
#
#
#
# 4.4. enable-remote-http-toggle
+# ===============================
#
# Specifies:
#
#
#
# 4.5. enable-edit-actions
+# =========================
#
# Specifies:
#
#
#
# 4.6. enforce-blocks
+# ====================
#
# Specifies:
#
#
#
# 4.7. ACLs: permit-access and deny-access
+# =========================================
#
# Specifies:
#
#
# Type of value:
#
-# src_addr[/src_masklen] [dst_addr[/dst_masklen]]
+# src_addr[:port][/src_masklen] [dst_addr[:port][/dst_masklen]]
#
-# Where src_addr and dst_addr are IP addresses in dotted decimal
-# notation or valid DNS names, and src_masklen and dst_masklen are
-# subnet masks in CIDR notation, i.e. integer values from 2 to 30
-# representing the length (in bits) of the network address. The
-# masks and the whole destination part are optional.
+# Where src_addr and dst_addr are IPv4 addresses in dotted
+# decimal notation or valid DNS names, port is a port number, and
+# src_masklen and dst_masklen are subnet masks in CIDR notation,
+# i.e. integer values from 2 to 30 representing the length
+# (in bits) of the network address. The masks and the whole
+# destination part are optional.
+#
+# If your system implements RFC 3493, then src_addr and dst_addr
+# can be IPv6 addresses delimeted by brackets, port can be a
+# number or a service name, and src_masklen and dst_masklen can
+# be a number from 0 to 128.
#
# Default value:
#
# Unset
#
+# If no port is specified, any port will match. If no src_masklen
+# or src_masklen is given, the complete IP address has to match
+# (i.e. 32 bits for IPv4 and 128 bits for IPv6).
+#
# Effect if unset:
#
# Don't restrict access further than implied by listen-address
# names. If a DNS name resolves to multiple IP addresses, only
# the first one is used.
#
+# Some systems allow IPv4 clients to connect to IPv6 server
+# sockets. Then the client's IPv4 address will be translated by the
+# system into IPv6 address space with special prefix ::ffff:0:0/96
+# (so called IPv4 mapped IPv6 address). Privoxy can handle it
+# and maps such ACL addresses automatically.
+#
# Denying access to particular sites by ACL may have undesired
# side effects if the site in question is hosted on a machine
# which also hosts other sites (most sites are).
# permit-access 192.168.45.64/26
# deny-access 192.168.45.73 www.dirty-stuff.example.com
#
+# Allow access from the IPv4 network 192.0.2.0/24 even if listening
+# on an IPv6 wild card address (not supported on all platforms):
+#
+# permit-access 192.0.2.0/24
+#
+#
+# This is equivalent to the following line even if listening on
+# an IPv4 address (not supported on all platforms):
+#
+# permit-access [::ffff:192.0.2.0]/120
#
#
# 4.8. buffer-limit
+# ==================
#
# Specifies:
#
#
#
# 5. FORWARDING
+# ==============
#
# This feature allows routing of HTTP requests through a chain of
# multiple proxies.
#
#
# 5.1. forward
+# =============
#
# Specifies:
#
# to denote "all URLs". http_parent[:port] is the DNS name or
# IP address of the parent HTTP proxy through which the requests
# should be forwarded, optionally followed by its listening port
-# (default: 8080). Use a single dot (.) to denote "no forwarding".
+# (default: 8000). Use a single dot (.) to denote "no forwarding".
#
# Default value:
#
# If http_parent is ".", then requests are not forwarded to
# another HTTP proxy but are made directly to the web servers.
#
+# http_parent can be a numerical IPv6 address (if RFC 3493 is
+# implemented). To prevent clashes with the port delimiter,
+# the whole IP address has to be put into brackets. On the other
+# hand a target_pattern containing an IPv6 address has to be put
+# into angle brackets (normal brackets are reserved for regular
+# expressions already).
+#
# Multiple lines are OK, they are checked in sequence, and the
# last match wins.
#
# forward .isp.example.net .
#
#
+# Parent proxy specified by an IPv6 address:
+#
+# forward / [2001:DB8::1]:8000
+#
#
+# Suppose your parent proxy doesn't support IPv6:
#
-# 5.2. forward-socks4 and forward-socks4a
+# forward / parent-proxy.example.org:8000
+# forward ipv6-server.example.org .
+# forward <[2-3][0-9a-f][0-9a-f][0-9a-f]:*> .
+#
+#
+# 5.2. forward-socks4, forward-socks4a and forward-socks5
+# ========================================================
#
# Specifies:
#
# denote "all URLs". http_parent and socks_proxy are IP addresses
# in dotted decimal notation or valid DNS names (http_parent may
# be "." to denote "no HTTP forwarding"), and the optional port
-# parameters are TCP ports, i.e. integer values from 1 to 64535
+# parameters are TCP ports, i.e. integer values from 1 to 65535
#
# Default value:
#
# target hostname happens on the SOCKS server, while in SOCKS 4
# it happens locally.
#
+# With forward-socks5 the DNS resolution will happen on the remote
+# server as well.
+#
+# socks_proxy and http_parent can be a numerical IPv6 address
+# (if RFC 3493 is implemented). To prevent clashes with the port
+# delimiter, the whole IP address has to be put into brackets. On
+# the other hand a target_pattern containing an IPv6 address has
+# to be put into angle brackets (normal brackets are reserved
+# for regular expressions already).
+#
# If http_parent is ".", then requests are not forwarded to another
# HTTP proxy but are made (HTTP-wise) directly to the web servers,
# albeit through a SOCKS proxy.
# To chain Privoxy and Tor, both running on the same system,
# you would use something like:
#
-# forward-socks4a / 127.0.0.1:9050 .
+# forward-socks5 / 127.0.0.1:9050 .
#
#
# The public Tor network can't be used to reach your local network,
#
#
#
-#
# 5.3. forwarded-connect-retries
+# ===============================
#
# Specifies:
#
# manually. Start with a small value and check Privoxy's logfile
# from time to time, to see how many retries are usually needed.
#
+# Due to a bug, this option currently also causes Privoxy to
+# retry in case of certain problems with direct connections.
+#
# Examples:
#
# forwarded-connect-retries 1
forwarded-connect-retries 0
#
#
-# 5.4. accept-intercepted-requests
+# 6. MISCELLANEOUS
+# =================
+#
+# 6.1. accept-intercepted-requests
+# =================================
#
# Specifies:
#
accept-intercepted-requests 0
#
#
-# 5.5. allow-cgi-request-crunching
+# 6.2. allow-cgi-request-crunching
+# =================================
#
# Specifies:
#
allow-cgi-request-crunching 0
#
#
-# 5.6. split-large-forms
+# 6.3. split-large-forms
+# =======================
#
# Specifies:
#
split-large-forms 0
#
#
-# 6. WINDOWS GUI OPTIONS
+# 6.4. keep-alive-timeout
+# ========================
+#
+# Specifies:
+#
+# Number of seconds after which an open connection will no longer
+# be reused.
+#
+# Type of value:
+#
+# Time in seconds.
+#
+# Default value:
+#
+# None
+#
+# Effect if unset:
+#
+# Connections are not kept alive.
+#
+# Notes:
+#
+# This option allows clients to keep the connection to Privoxy
+# alive. If the server supports it, Privoxy will keep the
+# connection to the server alive as well. Under certain
+# circumstances this may result in speed-ups.
+#
+# By default, Privoxy will close the connection to the server if
+# the client connection gets closed, or if the specified timeout
+# has been reached without a new request coming in. This behaviour
+# can be changed with the connection-sharing option.
+#
+# This option has no effect if Privoxy has been compiled without
+# keep-alive support.
+#
+# Note that a timeout of five seconds as used in the default
+# configuration file significantly decreases the number of
+# connections that will be reused. The value is used because some
+# browsers limit the number of connections they open to a single
+# host and apply the same limit to proxies. This can result in a
+# single website "grabbing" all the connections the browser allows,
+# which means connections to other websites can't be opened until
+# the connections currently in use time out.
+#
+# Several users have reported this as a Privoxy bug, so the default
+# value has been reduced. Consider increasing it to 300 seconds
+# or even more if you think your browser can handle it. If your
+# browser appears to be hanging it can't.
+#
+# Examples:
+#
+# keep-alive-timeout 300
+#
+keep-alive-timeout 5
+#
+#
+# 6.5. default-server-timeout
+# ============================
+#
+# Specifies:
+#
+# Assumed server-side keep-alive timeout if not specified by
+# the server.
+#
+# Type of value:
+#
+# Time in seconds.
+#
+# Default value:
+#
+# None
+#
+# Effect if unset:
+#
+# Connections for which the server didn't specify the keep-alive
+# timeout are not reused.
+#
+# Notes:
+#
+# Enabling this option significantly increases the number of
+# connections that are reused, provided the keep-alive-timeout
+# option is also enabled.
+#
+# While it also increases the number of connections problems when
+# Privoxy tries to reuse a connection that already has been closed
+# on the server side, or is closed while Privoxy is trying to
+# reuse it, this should only be a problem if it happens for the
+# first request sent by the client. If it happens for requests
+# on reused client connections, Privoxy will simply close the
+# connection and the client is supposed to retry the request
+# without bothering the user.
+#
+# Enabling this option is therefore only recommended if the
+# connection-sharing option is disabled.
+#
+# It is an error to specify a value larger than the
+# keep-alive-timeout value.
+#
+# This option has no effect if Privoxy has been compiled without
+# keep-alive support.
+#
+# Examples:
+#
+# default-server-timeout 60
+#
+#default-server-timeout 60
+#
+#
+# 6.6. connection-sharing
+# ========================
+#
+# Specifies:
+#
+# Whether or not outgoing connections that have been kept alive
+# should be shared between different incoming connections.
+#
+# Type of value:
+#
+# 0 or 1
+#
+# Default value:
+#
+# None
+#
+# Effect if unset:
+#
+# Connections are not shared.
+#
+# Notes:
+#
+# This option has no effect if Privoxy has been compiled without
+# keep-alive support, or if it's disabled.
+#
+# Notes:
+#
+# Note that reusing connections doesn't necessary cause
+# speedups. There are also a few privacy implications you should
+# be aware of.
+#
+# If this option is effective, outgoing connections are shared
+# between clients (if there are more than one) and closing the
+# browser that initiated the outgoing connection does no longer
+# affect the connection between Privoxy and the server unless
+# the client's request hasn't been completed yet.
+#
+# If the outgoing connection is idle, it will not be closed until
+# either Privoxy's or the server's timeout is reached. While
+# it's open, the server knows that the system running Privoxy is
+# still there.
+#
+# If there are more than one client (maybe even belonging to
+# multiple users), they will be able to reuse each others
+# connections. This is potentially dangerous in case of
+# authentication schemes like NTLM where only the connection
+# is authenticated, instead of requiring authentication for
+# each request.
+#
+# If there is only a single client, and if said client can keep
+# connections alive on its own, enabling this option has next to
+# no effect. If the client doesn't support connection keep-alive,
+# enabling this option may make sense as it allows Privoxy to keep
+# outgoing connections alive even if the client itself doesn't
+# support it.
+#
+# You should also be aware that enabling this option increases
+# the likelihood of getting the "No server or forwarder data"
+# error message, especially if you are using a slow connection
+# to the Internet.
+#
+# This option should only be used by experienced users who
+# understand the risks and can weight them against the benefits.
+#
+# Examples:
+#
+# connection-sharing 1
+#
+#connection-sharing 1
+#
+#
+# 6.7. socket-timeout
+# ====================
+#
+# Specifies:
+#
+# Number of seconds after which a socket times out if no data
+# is received.
+#
+# Type of value:
+#
+# Time in seconds.
+#
+# Default value:
+#
+# None
+#
+# Effect if unset:
+#
+# A default value of 300 seconds is used.
+#
+# Notes:
+#
+# For SOCKS requests the timeout currently doesn't start until
+# the SOCKS server accepted the request. This will be fixed in
+# the next release.
+#
+# Examples:
+#
+# socket-timeout 300
+#
+socket-timeout 300
+#
+#
+# 6.8. max-client-connections
+# ============================
+#
+# Specifies:
+#
+# Maximum number of client connections that will be served.
+#
+# Type of value:
+#
+# Positive number.
+#
+# Default value:
+#
+# None
+#
+# Effect if unset:
+#
+# Connections are served until a resource limit is reached.
+#
+# Notes:
+#
+# Privoxy creates one thread (or process) for every incoming
+# client connection that isn't rejected based on the access
+# control settings.
+#
+# If the system is powerful enough, Privoxy can theoretically deal
+# with several hundred (or thousand) connections at the same time,
+# but some operating systems enforce resource limits by shutting
+# down offending processes and their default limits may be below
+# the ones Privoxy would require under heavy load.
+#
+# Configuring Privoxy to enforce a connection limit below the
+# thread or process limit used by the operating system makes
+# sure this doesn't happen. Simply increasing the operating
+# system's limit would work too, but if Privoxy isn't the only
+# application running on the system, you may actually want to
+# limit the resources used by Privoxy.
+#
+# If Privoxy is only used by a single trusted user, limiting the
+# number of client connections is probably unnecessary. If there
+# are multiple possibly untrusted users you probably still want
+# to additionally use a packet filter to limit the maximal number
+# of incoming connections per client. Otherwise a malicious user
+# could intentionally create a high number of connections to
+# prevent other users from using Privoxy.
+#
+# Obviously using this option only makes sense if you choose a
+# limit below the one enforced by the operating system.
+#
+# Examples:
+#
+# max-client-connections 256
+#
+#max-client-connections 256
+
+#
+# 6.9. handle-as-empty-doc-returns-ok
+# ====================================
+#
+# Specifies:
+#
+# The status code Privoxy returns for pages blocked with
+# +handle-as-empty-document.
+#
+# Type of value:
+#
+# 0 or 1
+#
+# Default value:
+#
+# 0
+#
+# Effect if unset:
+#
+# Privoxy returns a status 403(forbidden) for all blocked pages.
+#
+# Effect if set:
+#
+# Privoxy returns a status 200(OK) for pages blocked with
+# +handle-as-empty-document and a status 403(Forbidden) for all
+# other blocked pages.
+#
+# Notes:
+#
+# This is a work-around for Firefox bug 492459: " Websites are no
+# longer rendered if SSL requests for JavaScripts are blocked by a
+# proxy. " (https:/ /bugzilla.mozilla.org/show_bug.cgi?id=492459)
+# As the bug has been fixed for quite some time this option
+# should no longer be needed and will be removed in a future
+# release. Please speak up if you have a reason why the option
+# should be kept around.
+#
+#handle-as-empty-doc-returns-ok 1
+#
+#
+# 1.6.10. enable-compression
+#
+# Specifies:
+#
+# Whether or not buffered content is compressed before delivery.
+#
+# Type of value:
+#
+# 0 or 1
+#
+# Default value:
+#
+# 0
+#
+# Effect if unset:
+#
+# Privoxy does not compress buffered content.
+#
+# Effect if set:
+#
+# Privoxy compresses buffered content before delivering it to
+# the client, provided the client supports it.
+#
+# Notes:
+#
+# This directive is only supported if Privoxy has been compiled
+# with FEATURE_COMPRESSION, which should not to be confused
+# with FEATURE_ZLIB.
+#
+# Compressing buffered content is mainly useful if Privoxy and the
+# client are running on different systems. If they are running on
+# the same system, enabling compression is likely to slow things
+# down. If you didn't measure otherwise, you should assume that
+# it does and keep this option disabled.
+#
+# Privoxy will not compress buffered content below a certain
+# length.
+#
+#enable-compression 1
+#
+#
+# 1.6.11. compression-level
+#
+# Specifies:
+#
+# The compression level that is passed to the zlib library when
+# compressing buffered content.
+#
+# Type of value:
+#
+# Positive number ranging from 0 to 9.
+#
+# Default value:
+#
+# 1
+#
+# Notes:
+#
+# Compressing the data more takes usually longer than compressing
+# it less or not compressing it at all. Which level is best
+# depends on the connection between Privoxy and the client. If
+# you can't be bothered to benchmark it for yourself, you should
+# stick with the default and keep compression disabled.
+#
+# If compression is disabled, the compression level is irrelevant.
+#
+# Examples:
+#
+# # Best speed (compared to the other levels)
+# compression-level 1
+#
+# # Best compression
+# compression-level 9
+#
+# # No compression. Only useful for testing as the added header
+# # slightly increases the amount of data that has to be sent.
+# # If your benchmark shows that using this compression level
+# # is superior to using no compression at all, the benchmark
+# # is likely to be flawed.
+# compression-level 0
+#
+#
+#compression-level 1
+#
+#
+# 7. WINDOWS GUI OPTIONS
+# =======================
#
# Privoxy has a number of options specific to the Windows GUI
# interface:
#
-
+#
# If "activity-animation" is set to 1, the Privoxy icon will animate
# when "Privoxy" is active. To turn off, set to 0.
#
#activity-animation 1
-
+#
# If "log-messages" is set to 1, Privoxy will log messages to the
# console window:
#
#log-messages 1
-
+#
# If "log-buffer-size" is set to 1, the size of the log buffer,
# i.e. the amount of memory used for the log messages displayed in
# the console window, will be limited to "log-max-lines" (see below).
# infinitely and eat up all your memory!
#
#log-buffer-size 1
-
+#
# log-max-lines is the maximum number of lines held in the log
# buffer. See above.
#
#log-max-lines 200
-
+#
# If "log-highlight-messages" is set to 1, Privoxy will highlight
# portions of the log messages with a bold-faced font:
#
#log-highlight-messages 1
-
+#
# The font used in the console window:
#
#log-font-name Comic Sans MS
-
+#
# Font size used in the console window:
#
#log-font-size 8
-
+#
# "show-on-task-bar" controls whether or not Privoxy will appear as
# a button on the Task bar when minimized:
#
#show-on-task-bar 0
-
+#
# If "close-button-minimizes" is set to 1, the Windows close button
# will minimize Privoxy instead of closing the program (close with
# the exit option on the File menu).
#
#close-button-minimizes 1
-
+#
# The "hide-console" option is specific to the MS-Win console version
# of Privoxy. If this option is used, Privoxy will disconnect from
# and hide the command console.